Need any help or advice?
+44 (0)1782 454499
Downloads (4)
 | Safety Datasheet (SDS) |  241 KB |
| Technical Datasheet (TDS) | 717 KB |
| XPREG Price List | 789 KB |
| XT135 Processing Guide | 706 KB |
Specification
Fabric Specification
| Fibre Specifics | Toray T700 12k | |
|---|---|---|
| Colour | Black | |
| Fibre Orientation | 0, 90 | |
| Type | Tooling Prepreg | |
| Resin Matrix | Epoxy | |
| Weave | 2 x 2 Twill | |
| Format | Woven Fabric | |
| Filament Count | 12k | |
| Fibre Type | Carbon Fibre | |
| Brand | XPREG |
Fibre Properties
| Out-life (at 20°C) | 21 | Days |
|---|---|---|
| Freezer-life (at -18°C) | 12 | Months |
| Min Cure Temp | 65 | °C |
| Max Cure Temp | 130 | °C |
| Max Service Temp | 130 | °C |
Weight and Dimensions
| Resin Weight | 59 | % |
|---|---|---|
| Width | 1250 | mm |
| Consolidated Thickness | 1 | mm |
| Areal Weight | 415 | g/m² |
General Properties
| Gross Weight | 1.06 | kg |
|---|---|---|
| Brand | XPREG |
Shipping Information
Classification
This product is not classed as dangerous goods for transport and can be shipped to all destinations without restriction.
Shipping 'Prepreg' Products
Prepreg materials are stored in our freezers at -20°C and are shipped from our warehouse still frozen.
This prepreg has a particularly short 'out-life' and for the best performance, the amount of time it spends at room temperature should be kept to an absolute minimum.
During summer months or periods of hot weather, only order this prepreg at the start of the week (Monday or Tuesday) to avoid adding extra shipping days over the weekend. Alternatively, please contact us to discuss alternative shipping arrangements.
Unless you plan to use the product immediately, it should be placed into frozen storage as soon as possible on receipt.
Customs Clearance
We remind all international customers that it is their responsibility clear goods through their local customs. Any delay caused during customs clearance is outside of our control and as such we cannot refund or replace materials which are found to be damaged or unusable on arrival as a result of delays during customs clearance.
Whilst such delays are very rare, we strongly advise all customers intending to import prepreg materials to contact their local customs agency to seek full clarification of the import procedure and whether delays are likely before placing an order. By placing an order for prepreg materials, you accept these conditions of sale.
Package Size
When packaged, this product is over 1m in length. A small additional handling charge will apply when shipping to some countries and regions. When applicable, this handling charge will be included in the automatic shipping calculation shown on the basket page.
Delivery Cost
To find the availability and cost for delivery of this item to your address, add it to your basket and then use the instant shipping calculator on the basket page.
XT135/B 415g 12k Tooling Prepreg Carbon (1250mm)
- XPREG
- XT135B-C1212T2-415(1250)-1
- No reviews
Backing ply for our XT135 out-of-autoclave prepreg carbon fibre tooling system. This is an uncured prepreg material and requires an oven or autoclave to cure it.
The XT135 tooling system can be cured in an oven under vacuum pressure only and used to produce high quality carbon fibre moulds/tools suitable for high temperature use. A minimum of two layers of this heavy 415gsm 2x2 twill backing ply should be combined with a single layer of surface ply.
This prepreg reinforcement is 1.25m (1250mm) wide and sold in a choice of prepacked roll lengths.
PRODUCT VERSIONS
Roll Length
AVAILABILITY:4 in stock available for immediate shipping
20 more can built in 2-3 days
We won’t be beaten on price!
If you believe you’re buying an equivalent product cheaper elsewhere, contact us to discuss your requirements.
XPREG® XT135 is a specialist out of autoclave carbon fibre tooling prepreg. It is designed to produce dimensionally accurate carbon fibre composite moulds using vacuum bag and oven cure only.
The tooling system is made up of XT135/S surface ply and the XT135/B carbon fibre tooling prepreg backing ply listed on this page.
A lightweight composite mould suitable for modest production volumes can be produced using just one surface and two backing plies (subject to mould geometry) whilst the recommended laminate for a production mould is one surface and four backing plies. See technical datasheet for full details on suggested layups and layup considerations.
Typical Uses
XT135/B is an out of autoclave tooling prepreg backing layer part of the XT135 tooling system developed specifically for out-of-autoclave cure and as such uses a special gelcoat-like filled resin surface. XT135 should be used for the production of composite tools for cure and use out-of-autoclave.
If tools are required for autoclave use then we would suggest our XT200 autoclave-cure tooling prepreg which doesn't require filled resins and therefore offer slightly superior shrinkage and higher service temperatures.
The Sample Pack contains two 400x300mm (15.7x11.8") pieces of prepreg.
Further Information
Full details on the correct storage, handling and processing of XPREG XT135 can be found in safety and technical datasheets, and complete processing guide.
Storage & Handling
XPREG® XT135 should be stored frozen at -18°C in sealed plastic packaging.
XPREG® XT135 is a specialist out of autoclave carbon fibre tooling prepreg. It is designed to produce dimensionally accurate carbon fibre composite moulds using vacuum bag and oven cure only.
The tooling system is made up of XT135/S surface ply and the XT135/B carbon fibre tooling prepreg backing ply listed on this page.
A lightweight composite mould suitable for modest production volumes can be produced using just one surface and two backing plies (subject to mould geometry) whilst the recommended laminate for a production mould is one surface and four backing plies. See technical datasheet for full details on suggested layups and layup considerations.
Typical Uses
XT135/B is an out of autoclave tooling prepreg backing layer part of the XT135 tooling system developed specifically for out-of-autoclave cure and as such uses a special gelcoat-like filled resin surface. XT135 should be used for the production of composite tools for cure and use out-of-autoclave.
If tools are required for autoclave use then we would suggest our XT200 autoclave-cure tooling prepreg which doesn't require filled resins and therefore offer slightly superior shrinkage and higher service temperatures.
The Sample Pack contains two 400x300mm (15.7x11.8") pieces of prepreg.
Further Information
Full details on the correct storage, handling and processing of XPREG XT135 can be found in safety and technical datasheets, and complete processing guide.
Storage & Handling
XPREG® XT135 should be stored frozen at -18°C in sealed plastic packaging.
Specification
Fabric Specification
| Fibre Specifics | Toray T700 12k | |
|---|---|---|
| Colour | Black | |
| Fibre Orientation | 0, 90 | |
| Type | Tooling Prepreg | |
| Resin Matrix | Epoxy | |
| Weave | 2 x 2 Twill | |
| Format | Woven Fabric | |
| Filament Count | 12k | |
| Fibre Type | Carbon Fibre | |
| Brand | XPREG |
Fibre Properties
| Out-life (at 20°C) | 21 | Days |
|---|---|---|
| Freezer-life (at -18°C) | 12 | Months |
| Min Cure Temp | 65 | °C |
| Max Cure Temp | 130 | °C |
| Max Service Temp | 130 | °C |
Weight and Dimensions
| Resin Weight | 59 | % |
|---|---|---|
| Width | 1250 | mm |
| Consolidated Thickness | 1 | mm |
| Areal Weight | 415 | g/m² |
General Properties
| Gross Weight | 1.06 | kg |
|---|---|---|
| Brand | XPREG |
Unfortunately we do not stock any pre-pregs with a flexible resin. The only flexible resin we supply is our EF80 Flexible Epoxy Resin which is suitable for wet lay and vacuum bagged processes.
ASK YOUR OWN QUESTION
Customer Product Reviews for XT135/B 415g 12k Tooling Prepreg Carbon (1250mm)
SUBMIT YOUR OWN PRODUCT REVIEW
We publish all reviews for verified purchases. Submit your own review and help other customers with their choices.SUBMIT YOUR OWN PRODUCT REVIEW
We publish all reviews for verified purchases. Submit your own review and help other customers with their choices.Shipping Information
Classification
This product is not classed as dangerous goods for transport and can be shipped to all destinations without restriction.
Shipping 'Prepreg' Products
Prepreg materials are stored in our freezers at -20°C and are shipped from our warehouse still frozen.
This prepreg has a particularly short 'out-life' and for the best performance, the amount of time it spends at room temperature should be kept to an absolute minimum.
During summer months or periods of hot weather, only order this prepreg at the start of the week (Monday or Tuesday) to avoid adding extra shipping days over the weekend. Alternatively, please contact us to discuss alternative shipping arrangements.
Unless you plan to use the product immediately, it should be placed into frozen storage as soon as possible on receipt.
Customs Clearance
We remind all international customers that it is their responsibility clear goods through their local customs. Any delay caused during customs clearance is outside of our control and as such we cannot refund or replace materials which are found to be damaged or unusable on arrival as a result of delays during customs clearance.
Whilst such delays are very rare, we strongly advise all customers intending to import prepreg materials to contact their local customs agency to seek full clarification of the import procedure and whether delays are likely before placing an order. By placing an order for prepreg materials, you accept these conditions of sale.
Package Size
When packaged, this product is over 1m in length. A small additional handling charge will apply when shipping to some countries and regions. When applicable, this handling charge will be included in the automatic shipping calculation shown on the basket page.
Delivery Cost
To find the availability and cost for delivery of this item to your address, add it to your basket and then use the instant shipping calculator on the basket page.
RELATED PRODUCTS
CUSTOMERS ALSO PURCHASED
RELATED PRODUCTS
CUSTOMERS ALSO PURCHASED
100% SECURE
PAYMENT METHODS
Easy Composites Ltd, registered in England 7486797. All content copyright (C) Easy Composites Ltd, 2024. All rights reserved.